As an Amazon Associate I earn from qualifying purchases.
1. Yosoo #ad
Induction Power Heating Supply Module ZVS Low Voltage Heating Power Supply Module with Heating Coil Power Supply Heating Power Supply Module, Yosoo 5V-12V ZVS Heating Power Supply Module #adYosoo #ad
- Zvs heating power Source module including heating coil. We suggest the voltage is 5V to 12V, or the overload current or voltage lead to the smoked module. Maximum power 120w when 12V eddy - current heating. The width of the heated object is as far as possible between the 1/3 ~ 1/2 of the inner diameter of the heating coil, the maximum not more than 2/3! Ensure all the components welding right, power line connect in right way, than to set up an electric circuit.
Input voltage dc5v-12v we do not guarantee the module will work when the voltage is over 12V or less than 5V.
2. Bewinner1 #ad
Bewinner1 2500W ZVS Induction Heater Module Flyback Driver, PCB Heating Board Large Radiator with Spiral Copper Tube Crucible and Water Pump Pipe 12-4 #adBewinner1 #ad
- The output terminal uses three M4 copper columns in parallel, which can be connected to other outputs such as high-voltage packet. The power cord is fully covered with copper cover, which can increase the current and calorific value.
The heating plate is made of PCB grade, with stable performance. Using large radiator and large power supply, ensures better heat dissipation effect. Using 6 irfp260s and 12 parallel resonant capacitors, high power, high efficiency.
3. Yosoo #ad
Yosoo Low Voltage Induction Heating Board Module Tesla Coil 12V-48V Flyback Driver Heater DIY with Coil 1000W ZVS #adYosoo #ad
- Great customer service: if you have any inquiry, please don?¡¥t hesitate to email us, we will give you a response within 24 hours. 24v input with no load current of 3A, 48V input with no load current of 6A.
The first will start switching power supply voltage reaches 12V above and then access the induction heating circuit. Line provides excellent service and longevity. Eradicate the actual situation to select the input voltage, the general use of the words 24V or 36V power supply is enough.
4. Baosity #ad
Baosity ZVS Driver Module 20A Induction Heating Power Supply Board W/Ignition Coil #adBaosity #ad
- Molten aluminum power requirements: 24v 350w - 500W power supply 15A to 20A, melting point: 660 Degrees Celsius. With a 36v power supply completely into the new 30 * 30 graphite crucible input current of 25A. Spiral copper pipe size: Inside diameter 40 mm, high 45mm.
Working voltage :dc 24-36v, working current:20A, Power tube: IRFP260N 50 a 200 v. Melting copper, respectively, gold, power requirements: 36v 700w - 900w power supply 20A to 25A, 1065 Degrees Celsius, melting point: 1083 Degrees Celsius, silver, 962 Degrees Celsius.
5. Gazechimp #ad
Gazechimp ZVS Induction Heating Board Module DC 24-36V Flyback Driver Heater DIY +Coil #adGazechimp #ad
- Melting copper, power requirements: 36v 700w - 900w power supply 20a to 25A, melting point: 1083 Degrees Celsius, gold, silver, respectively, 1065 Degrees Celsius, 962 Degrees Celsius. Molten aluminum power requirements: 24v 350w - 500W power supply 15A to 20A, melting point: 660 Degrees Celsius.
Spiral copper pipe size: Inside diameter 40 mm, high 45mm. Working voltage :dc 24-36v, working current:20A, Power tube: IRFP260N 50 a 200 v. With a 36v power supply completely into the new 30 * 30 graphite crucible input current of 25A.
6. Keenso #ad
ZVS Heating Board Driver Module Low Voltage Induction Heating Board Power Supplement Module #adKeenso #ad
- Stable performance -- factory-made large inductor coils are wound with 1. 2 mm copper wire for more stable performance and consistent parameters. Fast heating speed -- using a 12-30v dc power supplement, the current is greater than 10A.
As an induction heating plate, the higher the voltage, the faster the heating rate and the higher the temperature. The driver board can be used for induction heating without burning, ensuring that all components are soldered correctly and the power cord is connected correctly, instead of setting up the circuit.
Error is small -- zvs driver module uses 5-band resistors with small error and stable performance.
The higher the voltage, the longer the arc. Excellent material--the drive module is made of high-standard 1. 6mm double-layer fiberglass board. It is made of high-quality materials and is resistant to corrosion and wear. Induction heating -- the amount of tin on the bottom of the board is large.
7. kbxstart #ad
Kbxstart 1000W ZVS Low Voltage Induction Heating Board Module Tesla coil Flyback Driver Heater DIY 20A 12V-48V #adkbxstart #ad
- 100% satisfaction guarantEED, Good after-sale support. If you have any problem, please contact with us directly. 1000w power- this section of induction heating using low-voltage DC power supply 12-48V Maximum current 20A, maximum power 1000W.
Large heat- the higher the voltage, but at the same time heat is also large, the effect is better, so to eradicate the actual situation to select the input voltage, the greater the heating current when the same thing, the general use of the words 24V or 36V power supply is enough.
Diy accessory- because of its moderate power, silver, annealing and other heat treatment, aluminum and other metals, Also can be used with a graphite crucible melting gold, copper, can be used for small parts DIY players do hardening, uniform heating fast, very convenient.
Warranty & services- we provided 12 month warranty. Up to 53v- when it works 53v power supply, heating fast, current can reach 30A. It can be used for diy players to make small parts quenching, annealing and other heat treatment, very convenient.
8. Hilitand #ad
DC12-36V 20A 1000W ZVS Driver Model Induction Heating Board Module Heater With Copper Tube 90x180x65mm #adHilitand #ad
- Good heat dissipation : this zvS adopted an anti static 42*35 large heat sink ensures a good heat dissipation effect. Large pcb: heating plate with large PCB design, component layout is sparse to heat dissipation.
Two output modes: the output end of the three pillars of parallel and 300V/25A terminals, two output modes, easy to use under different requirements.
Accurate sized holethe positioning hole and the positioning hole of the heat radiating fan of the board and the 9*9cm are exactly matched with the positioning hole of the board, and the 12V power supply is directly inserted on the board. Stable: power line design can increase the current heat radiation and makes the board smaller and more stable.
9. Paialu #ad
1800W ZVS Induction Heating Board Module Flyback Driver Heater+Tesla Coil+Fan #adPaialu #ad
- We make every effort to provide customers with satisfactory service. Any question, please feel free to contact me. Just search the model number in our store. We are a professional distributor of electronic components. We also sell other kinds of products.
The item is good quality. Package reference weight:Weight:1. 1kg 2. 43lb. We will test the product before shipping. Estimated delivery time: 6-24 daystrackable- We provide Expedited Shipping service : 2-7 days. Excluding handling time. If the order amount above US $120, we will use Expedited Shipping service for free.